DK Digital CDB-700 Manual do Utilizador descarregar pdf (Página 61)

Page 61 of 108

The CB6P2 platform is introduced to obtain a powerful and optimised solution to customers looking

for existing analogue input systems. It is based on OpenBus™ technology, but to meet existing

analogue systems it has an analogue input similar to HB40 and therefore OpenBus™ accessories

cannot be connected.

2. CB6P2 (MEDLINE

CARELINE

)

Combination Overview

CB6P2 is meant for use with:

LA27 std. motor with Hall (cable type ‘A’)

LA27 std. motor (cable type ‘B’),

LA31 std. / fast motor with / without Hall,

LA34 std. / small / fast motor with / without Hall (fast motor not max. load),

LA44 std. / fast motor with / without Hall (fast motor not max. load),

BL1 (only with 270W transformer type) with / without Hall,

HB7x, HL7x, HB8x, ACL/ACM/ACP (HB40-like)

Recommendations:

Battery Operation:

• If the battery voltage is at ‘low level’, a battery alarm beeps constantly when the HB/ACx is activated.

(Low level means that battery charging is necessary to maintain the best possible life time. Low level battery limit corresponds to approx. 19 V (+/- 5%).

• If the battery voltage is at ‘critical level’ the battery alarm function shuts down all operation immediately.

Critical level limit corresponds to approx. 17.5 V (+/- 5%).

• If battery back-up is applied it only commences battery charging when it is connected to the mains.

• A battery stored at 25° C has to be recharged every 6-7 months.

• Prior to ﬁrst use of LINAK batteries, please make sure that they are charged for 24 hours in order to reach proper function and

prolong the lifetime of the batteries.

• The longest lifetime is obtained when the battery is fully charged.

CB6S is part of the LINAK OpenBus™ product range – that provides more ﬂexible solutions no

matter which actuator concept is preferred. LA27C, LA31, LA34, BL1, BL4 with mini-ﬁt plug and std.

end-stop switch/signal switch are all supported. Please be aware the actuators must be used within

their current limits in order to maintain proper use and full compatibility within a system.

Three versions are offered:

CB6 OBL, CB6 OBMe and CB6 OBF (OBL = OpenBus Light; which is RELAY based and OBF

= OpenBus Full which is FET based).

(OBM = OpenBus Medium; which is RELAY based

3. CB6S (MEDLINE

CARELINE

)

Microprocessor

All control boxes with a microprocessor must be initialised before start-up.

A description of the initialisation procedure can be obtained from your LINAK dealer.

If an actuator is replaced, the micro-processor always has to be initialised before use (actuators with

reed/hall). If re-programmed, please ensure that the correct software is used.

4. CB7 (HOMELINE

)

Compared to other LINAK control boxes the CB7 is very small and compact in design.

The CB7 is designed to slide onto an LA31 actuator for easy ﬁtting e.g. in a recliner application

where “mounting” space is limited.

The control box function is divided in two parts. The actual control box CB7, which slides onto the

LA31 actuator and a separate external power supply transformer box TR6 or TR7, which can be wall

mounted or placed on the ﬂoor moulding next to the mains.

The control box is only ﬁtted with low voltage electronic components and the connection between

the CB7 and transformer is via a 24 V power cable.

1 2 ... 56 57 58 59 60 61 62 63 64 65 66 ... 107 108

Comentários a estes Manuais

Sem comentários

DK Digital CDB-700 Manual do Utilizador Página 61

Comentários a estes Manuais

Manuais e produtos relacionados com não DK Digital CDB-700